Troubleshooting error on windows

May 22, 2009

whether your computer error? your computer may experience an error as we study in this article. There are some errors, such as DDL error, driver error, and error code, which can make your computer system to be an error also. The good news is, almost all the error messages that appear in Windows XP can bring to you and provide time for you to improve your computer system.

Following case example eror on device drivers of your PC:

STOP: 0xc000026C unable to load device driver Driver_Name

or

STOP: 0xc0000221 unable to load device driver Driver_Name

or

STOP: 0xc0000221. Bad image check sum, the image user32.dll is possibly corrupt. The header check sum does not match the computed check sum.

Error usually occurs on Windows XP on the system during the startup of your computer, and when a driver has been important ‘missing’ or corrupt. This error will appear if there is a file “User32.dll” a corrupt or ‘missing’. To fix this error, you can change the file that is corrupt. If you do not do this, you must reinstall the operating system back your Windows XP. To restore the damage or loss of a driver file User32.dll, I can see the following:

* You can enter the Windows XP installation CD into the CD-ROM and booting the PC to make sure booting from the CD come.
* In the “Welcome to Windows”, and press the letter R to open the “Recovery Console”. When the Recovery Console has been shown, you can run a command that is in the lower one by one, press Enter and type each command, and also change the name of the driver driver_name with the previous error.

cd windows \ system32 \ drivers
ren drivername.sys driver_name.old
copy F: \ i386 driver_name

Note: Changing the F: drive with the letter of the CD-ROM drive.
Finally, you can exit the Recovery Console, remove the Windows XP installation CD and restart your PC

If the error occurs in the user32.dll file, you can run the following instructions in the Recovery Console:

cd windows \ system32
ren user32.dll user32.old
expand F: \ i386 \ user32.dl_ c: \ windows \ system32 \ user32.dll

If you still can not fix the error with the instructions above, you can repair your installation of Windows XP. You can do this by selecting the option that is on display “Welcome to Windows”, which appear when booting a PC from Windows XP installation CD.

To prevent software or drivers that can make your computer system error, you can run several prevention. You can use the antivirus and antispyware tool with the latest update and run the scanning routine to ensure that your PC is not infected with the virus or the like. You should also keep the PC and your work environment, with open and clean your PC and the periodic check that all connectors and the card was seated properly on the motherboard. Still, most importantly, make sure you can register your Windows error free registry cleaner tool with a reliable and efficient. and following article for the error in the taskmanager (to enable taskmanager, cmd and regedit)


A D V E R T I S E M E N T





Related Post:

3 Responses to “Troubleshooting error on windows”

  1. Improve the operating system without re-install says:
    May 23, 2009 at 12:30 pm

    [...] tips to improve the operating system without re-install the windows (which may be caused by some windows troubleshooting) 1. Fix Installation If Windows XP is broken (corrupted) which does not have any other operating [...]

  2. disable autoPlay from Gpedit says:
    May 24, 2009 at 9:32 am

    [...] your computer have a problem on the windwos (trouble shooting on windows)? may be one cause is a virus, here is a few tips to overcome the problem on the computer, to avoid [...]

  3. Disk Clean up and Disk Deframenter says:
    May 27, 2009 at 6:50 am

    [...] be one of the tips to avoid troubleshooting the windows is to run Disk Defragmenter and Disk Cleanup (for caring the [...]

Leave a Reply